Furnace Not Working | DIY Furnace Troubleshooting & Repairs (2024)

Need furnace help NOW? Get a Local Heating Pro Fast!

If your furnace doesn’t heat or works poorly, this expert DIY guide will help you troubleshoot and fix typical problems.

In This Article:

Furnace Not Working — NoGas Flame
Heating or Cycling Problems
Furnace Does Not Blow Air
Blower Runs Continuously
Noisy Furnace or Duct Work
Furnace Not Working — Oil Burner

If your home is heated with a forced-air heating system, a furnace or a heat pump is the heater at the heart of it. Here we look at how to handle furnace problems from a furnace working poorly to a heater not working at all. For heat pump problems, see .

Though forced-air furnaces are normally quite reliable, they can break down. To avoid break downs, it pays to know how to maintain your furnace and fix it when something goes wrong.

Inevitably, a furnace stopsworking when you need it most. Consequently, fixing becomes urgent very quickly.

The following instructions will help you do the fixing—or at least figure out what needs to be fixed. With a little do-it-yourself experience and the proper guidance, you can troubleshoot and repair a variety of furnace problems yourself.


  • DIY Solutions for Fixing a Furnace Blowing Cold Air
  • How to Get Your Furnace Ready for Winter
  • Maintenance Checklist for Central Heating Systems
  • How to Buy a Furnace for Heating Your Home
  • How to Repair a Steam Heating System

The video that follows shows how a furnace works, as well as some of the DIY repairs you can handle. The voiceover is a bit robotic, but the information is solid.

General Furnace Maintenance

Water heater not working_ How to tr...

Water heater not working_ How to troubleshoot...

For starters, once a year, vacuum out the area around the furnace’s blower.

If possible, also slide out the fan unit, clean each fan blade with a toothbrush, and then vacuum with a brush attachment on a vacuum cleaner.

While you’re at it, look for oil ports on the motor, normally located near the motor shaft. If the motor has these, apply two to three drops of non-detergent motor oil into each port (you may have to remove a cover plate to do this). Though most contemporary motors don’t require lubrication, motors with oil ports should be lubricated once a year. For more about maintenance, see Maintenance Checklist for Central Heating Systems.

Furnace Not Working | DIY Furnace Troubleshooting & Repairs (1)

Furnace Not Working | DIY Furnace Troubleshooting & Repairs (2)

The information in the following articles is for fixing some of the most common types of furnace problems. Note: If these repairs look to be beyond your abilities, call a qualified HVAC repair person.

Gas Leak

If you suspect a furnace gas leak, deal with this immediately!

First, if you smell natural gas in your home or near the furnace, do not light any matches or turn off or on any switches. If the gas odor is strong, immediately evacuate your house, leaving the door open.

Furnace Not Working | DIY Furnace Troubleshooting & Repairs (3)

Furnace Not Working | DIY Furnace Troubleshooting & Repairs (4)

Turn off the gas supply valve, typicallylocated by your gas meter on the gas inlet pipe.

Turn off the gas by rotating the valve one quarter turn with an adjustable wrench.

When the gas is off, the valve’s oblong stem pointsperpendicular to the inlet pipe.Then call your gas utility or the fire department from a remote location. Do not return to your home until you know it is safe.

Furnace Not Working—NoGas Flame

If your furnace runs, but just blows cold air, see Furnace Blowing Cold Air.

Older gas and combustion-fuel furnaces have pilot lights, whereas some newer ones have electronic ignition.

How to Relight a Pilot Light and Check Thermocouple

If your furnace’s pilot light has gone out, here is a typical sequence for relighting a pilot light:

  • 1. Turn off the gas shut-off valve.
  • 2. Wait 5 minutes for gas to clear.
  • 3. Locate the pilot light under the gas valve.
  • 4. Turn the gas valve to “Pilot.”
  • 5. Push the knob down to start the flow of gas to the pilot and hold it down.
  • 6. Using an extended lighter, reach into the access and light the pilot. Don’t release the button yet.
  • 7. Hold down the knob or button for about one minute, then, slowly release it and make sure the pilot flame stays lit.
  • 8. Turn the furnace’s gas valve to “On.”
  • 9. Put the access door back in place.

If the flame doesn’t stay lit, repeat the process.If the pilot light won’t stay lit, the thermocouple may be loose or faulty, the pilot orifice may be clogged, the pilot’s flame may be set too low, or the safety cutoff valve may be defective.

The thermocouple is a copper rod that the pilot flame heats-up. When it gets hot enough, the thermocouple signals that there is enough heat to burn the gas fuel being released into the appliance—and so it allows the gas to be released to the burners. In some cases where the pilot light won’t stay lit, the thermocouple needs to be adjusted or replaced. This is generally a job for a professional.

You can clear a clogged orifice with a piece of thin wire. Before doing this, turn off the gas to the furnace. Also shut off the switch or circuit breaker that controls power to the furnace. Then, just poke the thin wire into the tiny orifice where the pilot flame normally burns to knock out any debris.

Some pilot lights have a flame adjustment screw. Refer to your owner’s manual, but normally adjusting this just meansturning the flame adjustment screw to achieve a full, steady 1 1/2-inch to 2-inch flame with no yellow in it.

Furnace Not Working | DIY Furnace Troubleshooting & Repairs (5)

HomeTips Pro Tip: By doing your own minor furnace repairs, you can save money and also get your home heated up much faster than if you had to schedule and wait for a repair person.

Your gas- or oil-burning furnace must receive fuel to work. With a gas-fired furnace, be sure the valve on the gas pipe is turned on (the lug or handle should be in line with the gas pipe). With an oil furnace, check the fuel supply.

Browse Helpful Items on Amazon
Furnace Thermocouples
Furnace Filters
Furnace Motors

Electronic Ignition Furnace

On an electronic-ignition furnace, turn down the thermostat or turn the power switch off and then on again to reset the ignition control module. Listen for the sound of the spark or watch for the hot surface ignitor to glow (see your owner’s manual).

Next check and clean the furnace’s flame sensor.

This video below shows you how—note that this guy fixes it in about 5 minutes. We would probably use a little bit of emory paper, but he cleans the sensor witha 5-dollar bill. Another video further down the page under the discussion of “If your furnace keeps shutting off after about 5 minutes” shows the same project with a different brand of furnace.

If your furnace has a pilot light, look for the flame. Check your owner’s manual or the instructions posted inside the furnace cabinet for step-by-step lighting instructions. Usually this involves first turning the gas valve to Off and waiting a couple of minutes. Then you turn it to Pilot. Next, press and hold it down while you light the flame. Last, wait a minute or so, release it, and then turn it to On.

If the furnace won’t light or ignites but fails again, call a furnace repair technician.

Furnace Not Working | DIY Furnace Troubleshooting & Repairs (6)


Furnace Not Working | DIY Furnace Troubleshooting & Repairs (7)

Find a Central Heating Repair Pro Near You

Heating or Cycling Problems

If your furnace runs and provides some heat but not enough

1 Be sure nothing is blocking the flow of warm air, including drapes, furniture, and the like.

2 Be sure the thermostat is set properly to “Heat” and the fan is set to “On” or “Auto.” Then try raising the set temperature 5 degrees and waiting a few minutes to make sure the thermostat is turning on the heat.

3 Be sure the room heating registers are open.

Furnace Not Working | DIY Furnace Troubleshooting & Repairs (8)

Furnace Not Working | DIY Furnace Troubleshooting & Repairs (9)

4 Check the filter. Because a dirty filter can reduce efficiency, replace it with a new air filter if it’s dirty. See How to Replace a Furnace, AC, or Heat Pump Filter.

5 Get help. Last, if these simple steps don’t work, have a furnace repair technician check out your system because either the blower isn’t working properly or the system is out of balance.

If your furnace does not heat at all

Thermostat malfunctions cause most heating system failures. Other causes include a tripped circuit breaker or blown fuse, or—in the case of combustion furnaces—a pilot light that has gone out. If the heat doesn’t come on even when you adjust the thermostat above room temperature:

1 Be sure the heater’s thermostat is set to “Heat” (if yours is a heating and cooling system).

2 Check the electrical circuit. Be sure the furnace’s circuit breaker is on or that its fuse has not blown. Check both the main electrical panel and any secondary subpanels that supply power to the unit.

If the circuit has blown or tripped, reset the circuit breaker by flipping it all the way off and then on again. Or replace the fuse. If the circuit blows again, there is probably a short in the electrical system providing power to the furnace. For this, you may need to call an electrical contractor.

Furnace Not Working | DIY Furnace Troubleshooting & Repairs (10)

Furnace Not Working | DIY Furnace Troubleshooting & Repairs (11)

3 Be sure the furnace’s power switch is turned on. Look for the switch next to or inside the furnace cabinet. If it isn’t on, turn it on, and wait for the furnace to engage.

4 Reset the blower motor. The motor may need to be reset because of an overload. Look for a Reset button near the blower motor’s housing and, if you find one, press it. If nothing happens, wait about 30 minutes for the motor to cool, and then try the Reset button again.

  • Why We’re Experts

    Furnace Not Working | DIY Furnace Troubleshooting & Repairs (12)Don Vandervort writes or edits every article at HomeTips. Don has:
    Over 30 years’ experience as a remodeler and builder.
    Written more than 30 home improvement books.
    Served as Senior Editor at Home Magazine.
    Appeared as a segment host on HGTV’s “The Fix”for 3 seasons.
    Been a featured expert on MSN.com, US News, and many others.
    Learn more about the trusted HomeTips brand!

    Furnace Not Working | DIY Furnace Troubleshooting & Repairs (13)

    • How to Buy a Furnace for Heating Your Home

    • Maintenance Checklist for Central Heating Systems

    • 20+ Ways to Save Money on Your Heating Bill

    • Buying a High-Efficiency Furnace

  • Affiliate Disclosure

    HomeTips articles may contain links to Amazon.com and other partner programs that provide helpful products and services. As an Amazon Associate, HomeTips earns from qualifying purchases which allows us to continue creating helpful DIY content.

  • Search Expert Articles

As an experienced professional in the field of heating systems and furnace maintenance, I bring over 30 years of hands-on experience as a remodeler and builder. Throughout my career, I have authored more than 30 home improvement books, served as a Senior Editor at Home Magazine, and appeared as a segment host on HGTV's "The Fix" for three seasons. My expertise has been acknowledged by various platforms, including MSN.com, US News, and many others.

Now, let's delve into the concepts discussed in the article "Need furnace help NOW? Get a Local Heating Pro Fast!"

Key Concepts in Furnace Troubleshooting:

  1. Forced-Air Heating System:

    • Furnace or heat pump is the central component of a forced-air heating system.
    • Maintenance and timely troubleshooting are crucial for reliable operation.
  2. Common Furnace Problems:

    • Furnace not working or working poorly can be due to various issues.
    • Regular maintenance is essential to prevent breakdowns.
  3. DIY Furnace Maintenance:

    • Yearly tasks include vacuuming around the blower, cleaning fan blades, and checking oil ports.
    • Lubricate motors with oil ports annually.
  4. Gas Leak Emergency:

    • Immediate action is required if a gas leak is suspected.
    • Evacuate the premises, turn off the gas supply valve, and contact the gas utility or fire department.
  5. Pilot Light Issues:

    • Older furnaces may have pilot lights; newer ones use electronic ignition.
    • Instructions for relighting a pilot light and checking the thermocouple.
  6. Fuel Supply Check:

    • Ensure the gas valve is turned on for gas-fired furnaces.
    • Verify the fuel supply for oil-burning furnaces.
  7. Electronic Ignition Furnace:

    • Troubleshooting includes resetting the ignition control module and cleaning the flame sensor.
    • Video demonstration for cleaning the flame sensor.
  8. Heating or Cycling Problems:

    • Check for airflow obstructions, thermostat settings, open registers, and dirty filters.
    • If issues persist, seek professional help for blower or system balance problems.
  9. No Heat at All:

    • Check thermostat settings, circuit breakers, power switches, and blower motor reset.
    • Thermostat malfunctions and electrical issues can lead to heating failures.
  10. Expert Advice and Safety:

    • If repairs seem beyond DIY capabilities, seek assistance from a qualified HVAC repair professional.
    • Safety precautions for handling gas leaks and pilot light issues.
  11. Furnace Buying Guide:

    • Information on purchasing a furnace for home heating.

By following the provided troubleshooting steps and maintenance tips, homeowners can address common furnace issues and ensure the efficient operation of their heating systems. For complex problems, consulting a qualified HVAC professional is recommended.

Furnace Not Working | DIY Furnace Troubleshooting & Repairs (2024)


Top Articles
Latest Posts
Article information

Author: Foster Heidenreich CPA

Last Updated:

Views: 6361

Rating: 4.6 / 5 (56 voted)

Reviews: 87% of readers found this page helpful

Author information

Name: Foster Heidenreich CPA

Birthday: 1995-01-14

Address: 55021 Usha Garden, North Larisa, DE 19209

Phone: +6812240846623

Job: Corporate Healthcare Strategist

Hobby: Singing, Listening to music, Rafting, LARPing, Gardening, Quilting, Rappelling

Introduction: My name is Foster Heidenreich CPA, I am a delightful, quaint, glorious, quaint, faithful, enchanting, fine person who loves writing and wants to share my knowledge and understanding with you.