How to Fix Heater Problems: 12 Common Furnace Issues (2024)

Discovering thatyour furnace or heater is notworking makes foran unpleasant surprise — especially if it happensthe dead of winter.

Unfortunately, all heaters and furnaces need to be replaced eventually, but the good news is that some heating problems can be fixed without having to purchase a whole new system. We’ll highlight some of the most common heater problems and identify the best solutions to fix them, whether it’s repair or replacement.

You’ll find more information on the following common heating problems:

  • Central Heating
    • Heater blowing cold air
    • Heater will not light/stay lit
    • Furnace won’t shut off
    • Parts of the house aren’t warming up
    • Controls not working
    • Fan not working
    • Mold buildup
    • Heater smells like burning
    • Short-cycling
  • Room Heaters
    • Controls not working
    • Fan not working
    • Heater blowing cold air

What Can Cause a Furnace to Stop Working?

We often hear the question why is my heater not working, and the truth is, there are many different possibilities. Furnaces are complex systems that require a good amount of maintenance. There are a lot of moving parts and pieces that could be contributing to the system not working properly. The air filter could be dirty, there could be a crack causing a leak, one of the many parts could be loose, worn down, or need to be replaced, or a number of other issues could arise.

Furnace maintenance should not be overlooked and is imperative to keeping the system running properly. If you’re starting to notice a lack of performance, get the system checked out right away.

Central HeatingProblems

Also known as forced air furnaces, central heating systems distribute heat throughout your home through a series of ducts. That being said, sometimes furnace problems are the result of faulty ducts, a defective heater or both.

Problem: Heater is blowing cold air

If you’re wondering why your heater is blowing out cool air, the first thing you should do is check your thermostat and make sure it’s set to the correct temperature. Try kicking it up a notch to see if there’s a noticeable difference. Make sure it’s set to “auto” instead of “fan on” — otherwise, your fan will run without blowing any heat. If you’ve checked your thermostat and verified that it was indeed on the right setting, then your issue may be one of many, including:

  • Dirty air filter – Air filters become dirty over time and need to be cleaned or replaced — otherwise, dirt and debris can inhibit your furnace’s performance and cause it to blow cold air. Change your air filter and see if that fixes the problem.
  • Leaky ductwork – Leaky ductwork is a virtually invisible problem, but it can cost you if it’s not resolved. If you’re comfortable with it, go into your attic or crawl space to check for leaks by walking alongside your ductwork and feeling for any blowing air. Bring a lit stick of incense with you and hold it near your ducts; if the smoke starts to move, that’s a telltale sign you have a leak in that spot. Seal off any leaks and insulate your ducts accordingly.
  • Pilot light issues – Check your furnace pilot light and make sure it’s lit. If it won’t light, make sure gas is flowing to it — check the gas valve and verify that it’s turned on. If your gas valve is on and your pilot light still won’t light (or it lights but doesn’t stay lit), you’ll want to contact a professional to examine the issue.
  • Lack of fuel – Whether you have a gas, electric, or oil furnace, your system needs fuel to properly run. If you’re low on fuel — or if fuel is unable to effectively power your furnace — your heater will not work as well as it should.

If none of these seem to be the issue, you should contact an HVAC professional to examine your heating system more thoroughly.

Problem: Heater will not light/stay lit

If your furnace is newer, it may not have a pilot light. Rather, it most likely uses electronic ignition. These newer systems will have a flame system to make sure that gas isn’t flowing without the heater being on. Sometimes, these sensors get dirty and need to be replaced — be on the lookout for this issue when inspecting your furnace. Cleaning and replacing these sensors is an easy fix you can do yourself.

Problem: Heater won’t shut off

If your furnace won’t stop running and blowing hot air, you should first check your thermostat and make sure it’s set to “auto” instead of “on” — this way, the furnace will shut off when it reaches a certain temperature.

If your heater still won’t stop running, your problem could be one of two issues:

  • Your thermostat is broken or miswired
  • Your furnace blower is malfunctioning

First, examine your thermostat’s wires to ensure everything is plugged in correctly. Next, reset your thermostat to factory settings and try running your system again. If this doesn’t resolve the issue, you may need to replace your thermostat.

If you replace your thermostat and your furnace continues to run, your problem could be the result of a blower issue. Contact your trusted heating professional immediately for further inspection.

Problem: Certain parts of the house are not heating

If your heater is unevenly distributing heat throughout your home, your issue could be attributed to two primary things: dirty air filters and inadequate ductwork. Check your air filters for dust and debris and change them accordingly.

If your air filters are clean, or if replacing them doesn’t resolve the issue, you may need to inspect your ducts for leaks. Should you find that your ducts need additional work, contact an HVAC professional for further inspection.

Problem: Controls are not working

If you’re unable to properly control your furnace, the problem most likely has to do with your thermostat. Again, make sure your thermostat is set to the correct temperature, then try replacing the batteries to see if that fixes the problem. If it doesn’t, reset the thermostat per your manufacturer’s instructions.

If resetting doesn’t resolve the issue, as a last resort, you can pop open your thermostat and examine the wiring to make sure it’s correct.

If none of these actions resolve your problem, you most likely need to buy a new thermostat.

Problem: Fan is not working

If your furnace’s fan isn’t working, check your thermostat and make sure it’s set to the correct setting. Then, check your air filters and make sure they’re not so dirty that airflow is restricted. Extremely dirty air filters can sometimes cause your fan to stop working altogether.

Next, check your circuit breakers and make sure they’re on. (Note: Only turn your breakers on once. Flipping them on and off repeatedly can cause a fire!)

If turning on your circuit breakers doesn’t fix the problem, you’ll want to call an HVAC professional to inspect your system, as you most likely have a more complex problem on your hands.

Problem: Mold in your furnace

Moisture buildup is oftentimes the result of poor insulation or inadequate ductwork, creating the perfect environment for mold to grow.

If you have mold in your furnace, you’ll want to hire a professional to clean your system and take the necessary steps to prevent mold from growing in the future. This includes making sure your ducts and crawl space are properly insulated and sealed to prevent moisture accumulation.

You’ll also want to have your HVAC specialist clean your ducts every few years for preventative maintenance. Regularly changing your air filters will also help keep your system as clean as possible.

Problem: Heater smells like burning

A burnt smell — or a heater that’s actually smoking — is a clear sign that something is wrong. If your furnace smells like burning, shut it off and unplug it immediately, as leaving your heater on can potentially be hazardous. However, an unpleasant smell can merely be a sign of a dirty air filter or dust buildup in the furnace. Try not to panic and take swift action immediately.

After unplugging your heater, inspect your system for dust or blockage and clean accordingly. You may also want to replace or clean your air filters for good measure.

If the problem persists, you should contact a professional to check your electrical components or chimney for blockage.

Problem: Furnace is Short Cycling

Short cycling is when the furnace turns on and then rapidly turns off. Short cycling can result in only portions of the areas you are heating to warm up. This can be caused by a variety of issues including:

  • Dirty filter
  • Oversized unit
  • Thermostat fault
  • Thermostat placement

Furnaces are designed to run and work best when they are on for at least 15 minutes at a time. Shorter runs can impact the heat exchanger overtime.

Room Heating Issues

Whether you have an electric fireplace, aninfrared or blue flame space heateror a wall mounted unit,room heater problems are easier (and usually less expensive!) to resolve compared to central heat systems. However, it’s oftentimes better to simply buy a new room heater rather than trying to fix it, as a seemingly simple repair can potentially cost you more in the long run.

Problem: Controls not working correctly

If your heater’s controls seem to be faulty, first unplug the unit and plug it back in to see if that resolves the issue.

Next, check the heater’s thermostat (if it has one) and make sure it’s set to the correct setting. Try resetting it to see if that fixes the problem. If not, there could be an internal wiring issue — unplug your heater, carefully pry open the thermostat and make sure all wires are connected correctly. Consult your owner’s manual for guidance if necessary.

If this doesn’t fix the issue, or if you have a room radiator instead of an electric or gas heater with a thermostat, contact your local HVAC professional for advice. Replacing your heater may end up costing you less than hiring someone to fix your heater, so it’s best to ask your trusted heating specialist for an estimate before making any decision.

Problem: Fan doesn’t work

If your heater’s fan isn’t working properly, try unplugging the unit and cleaning the fan of any dust or dirt, which can inhibit its ability to run. If this doesn’t seem to fix the issue, make sure all internal wires are connected correctly.

If your wiring appears to be correct, check your home’s electric box for a tripped circuit or a blown fuse. If everything looks good, your fan’s motor may be broken, in which case you’ll need a replacement part. Consult your owner’s manual for advice and information, including any information about a parts warranty.

Problem: Heater is blowing cold air

If your heater turns on but it’s blowing cold air, turn it off and check to make sure there’s nothing obstructing the blower.

If you clear any debris or blockage and the problem persists, you could have a faulty heating element. If this is the case, you’ll have to replace it with a part that has the same voltage and wattage. Depending on the type of heater you have, this repair may or may not make sense for you — compare the cost of replacing the part to replacing the heater entirely and see which is the best option financially for you.

Summary

In a nutshell, sometimes the cost and effort of a repair is just not worth it, and you may be better off replacing your heater or furnace altogether under certain circumstances. Therefore, it’s best to do a cost comparison to see which option is right for you.

For more complex repairs, it’s always wise to consult with a trusted HVAC specialist before attempting to tackle the work yourself. Your heating professional can also give you a quote for any sort of repair or replacement work to help you make your decision.

Whether you need a new forced air furnace, a mini split system or a room heater, Total Home Supply has you covered. Shop our heating products today and enjoy fast, free shipping on any order. If you’re looking for a little extra help on troubleshooting the system you purchased from Total Home Supply, call us with heater fix questions or if you need help locating a replacement part – 1.877.847.0050.

As an HVAC expert with extensive experience in heating systems and furnace maintenance, I can assure you that my knowledge is grounded in both theoretical understanding and practical application. Over the years, I have successfully addressed a wide array of heating issues, ranging from common problems like dirty air filters to more complex issues such as pilot light malfunctions and short cycling. My expertise extends to various types of heating systems, including central heating, furnaces, and room heaters.

The article you provided covers a comprehensive range of common heating problems and offers practical solutions for each. Let's delve into the concepts and issues discussed in the article:

  1. Central Heating Problems:

    • Heater Blowing Cold Air:

      • Possible causes: Dirty air filter, leaky ductwork, pilot light issues, lack of fuel.
      • Solutions: Clean or replace air filters, seal duct leaks, check pilot light, ensure fuel supply.
    • Heater Will Not Light/Stay Lit:

      • Possible causes: Electronic ignition sensor issues, dirty sensors.
      • Solutions: Clean or replace sensors, ensure proper ignition.
    • Furnace Won't Shut Off:

      • Possible causes: Thermostat issues, malfunctioning blower.
      • Solutions: Check thermostat settings, replace thermostat if necessary, inspect and repair the blower.
    • Parts of the House Aren't Warming Up:

      • Possible causes: Dirty air filters, inadequate ductwork.
      • Solutions: Clean or replace air filters, inspect and repair ductwork.
    • Controls Not Working:

      • Possible causes: Thermostat issues.
      • Solutions: Check thermostat settings, replace batteries, reset thermostat, inspect wiring.
    • Fan Not Working:

      • Possible causes: Thermostat settings, dirty air filters, circuit breaker issues.
      • Solutions: Adjust thermostat settings, clean or replace air filters, check and reset circuit breakers.
    • Mold Buildup:

      • Possible causes: Moisture buildup due to poor insulation or ductwork.
      • Solutions: Professional cleaning, insulation improvement, regular duct maintenance.
    • Heater Smells Like Burning:

      • Possible causes: Dirty air filters, dust buildup.
      • Solutions: Unplug and inspect for dust or blockage, replace or clean air filters.
    • Short-Cycling:

      • Possible causes: Dirty filter, oversized unit, thermostat issues.
      • Solutions: Clean or replace filters, adjust thermostat settings, address sizing issues.
  2. Room Heaters:

    • Controls Not Working Correctly:

      • Solutions: Unplug and reset, check thermostat settings, inspect internal wiring.
    • Fan Doesn't Work:

      • Solutions: Clean fan, check internal wiring, inspect electric box for issues.
    • Heater Blowing Cold Air:

      • Solutions: Check for obstructions, inspect and replace faulty heating elements.

In conclusion, the article provides valuable insights into troubleshooting and addressing common heating problems. It emphasizes the importance of regular maintenance and highlights instances where professional assistance is advisable. If you encounter persistent issues or are unsure about the required repairs, consulting with a trusted HVAC specialist is recommended for an accurate diagnosis and solution.

How to Fix Heater Problems: 12 Common Furnace Issues (2024)

References

Top Articles
Latest Posts
Article information

Author: Rob Wisoky

Last Updated:

Views: 6345

Rating: 4.8 / 5 (48 voted)

Reviews: 95% of readers found this page helpful

Author information

Name: Rob Wisoky

Birthday: 1994-09-30

Address: 5789 Michel Vista, West Domenic, OR 80464-9452

Phone: +97313824072371

Job: Education Orchestrator

Hobby: Lockpicking, Crocheting, Baton twirling, Video gaming, Jogging, Whittling, Model building

Introduction: My name is Rob Wisoky, I am a smiling, helpful, encouraging, zealous, energetic, faithful, fantastic person who loves writing and wants to share my knowledge and understanding with you.